AMSOIL Authorized Dealer
Premium Engine Care
WALTER & REGINA HAYES
CARL JUNCTION, MO
FREE SHIPPING on Qualifying Orders Over $100.
← Back to BlogChainsaw Care for Firewood Season in the Four States

Chainsaw Care for Firewood Season in the Four States

Once the leaves come down around Carl Junction and Joplin, you start hearing chainsaws on Saturday mornings. Somebody's bucking up a dead oak along the fence line, somebody else is filling the bed of the pickup for the wood stove, and after any good windstorm there are limbs to clean up all over the yard. For a lot of folks in the Four States, November through February is when the chainsaw does most of its work for the year. A few minutes of care before you pull the cord makes that work easier and keeps the saw starting every time you need it.

Start With Your Owner's Manual

Every saw is a little different. Your manual tells you the fuel-to-oil mix ratio, what kind of bar oil to use, how to set chain tension, and how often to clean the air filter and check the spark plug. Treat this post as a reminder list, and let the manual have the final word.

Mix Fresh Fuel, and Only What You'll Use

Most homeowner chainsaws are two-stroke engines, which means the oil is mixed right into the gas. Mix it at the ratio your saw's maker calls for, in a clean can marked for mixed fuel only, and write the date on it. AMSOIL points out that gasoline can start breaking down in as little as 30 days, and stale fuel is a common reason a saw won't start or runs rough. Mix what you'll burn in the next few weeks, not the whole winter's worth at once.

If you're shopping for two-stroke oil, AMSOIL's SABER Professional 100% Synthetic 2-Stroke Oil is made for handheld two-stroke equipment like chainsaws and trimmers, and AMSOIL says it also stabilizes fuel during storage. Check the product page and your manual to make sure the specs match your saw before you switch.

Don't Run the Bar Dry

Bar and chain oil and two-stroke oil are two different things, and one can't stand in for the other. The bar oil goes in its own reservoir and keeps the chain sliding along the bar instead of grinding against it. Top it off every time you fill the fuel tank. Before you start cutting, point the tip of the bar at a piece of cardboard or a light-colored stump and rev the saw for a few seconds; you should see a light line of oil spray off the chain. If you don't, clean the oil port and check the oiler before you go any further. AMSOIL makes a Semi-Synthetic Bar and Chain Oil with a tacky formula meant to cling to the chain.

Quick Checks Before You Cut

  • Chain tension: with the saw off, the chain should be snug on the bar but still pull around by hand (wear gloves). A chain that's too loose can jump off the bar; one that's too tight can bind and overheat. Follow the manual for how to adjust yours.
  • Sharpness: a sharp chain throws chips, not dust. If you're pushing hard and getting fine sawdust, it's time to sharpen or swap the chain.
  • Air filter: firewood cutting is dusty work. Knock out or clean the filter as often as the manual says, and more often when you're cutting a lot.
  • Spark plug: if the saw is hard to start even with fresh fuel, pull the plug and look at it. A fouled or worn plug is cheap to replace.
  • Bar groove and sprocket: clean packed sawdust out of the bar groove and from under the side cover now and then, and flip the bar every so often so it wears evenly, if your manual recommends it.
  • Safety gear: chaps, eye and ear protection, gloves, and good boots. It's not engine care, but it's the most important part of the job.

Storing It Between Jobs

A lot of saws sit for weeks between cutting days. If yours will sit a while, either run it on fuel that's been stabilized or drain the tank and run it until it stalls, whichever your manual recommends. AMSOIL also offers a Gasoline Stabilizer for straight gas that will sit. Wipe the saw down, put the bar cover on, and store it somewhere dry. Then it's ready the next time a limb comes down in the middle of the night.

Not Sure What Your Saw Takes?

Check our Vehicle Lookup Guide for exact AMSOIL recommendations, or browse AMSOIL's power equipment products. If you can't find your saw, give us a call and we'll look it up with you.

We're Here to Help

Walter and Regina Hayes are your local AMSOIL Dealers right here in Carl Junction. Whether you cut a cord a year for the fireplace or run saws for a living, we're glad to help you sort out what goes in each one. Request a free AMSOIL catalog, or become an AMSOIL Preferred Customer and save up to 25% off retail prices. You can reach us at 1-417-649-6776.

Header photo: "Old man cutting wood with a chainsaw. Front view" by Nenad Stojkovic, via Wikimedia Commons, licensed CC BY 2.0.

Ready to protect your engine with AMSOIL?

Questions? Call or text 1-417-649-6776 — Walter & Regina are happy to help.

Related Posts

SponsoredOak Creek Realty Group

Buying or selling a home in the Four States area? Walter Hayes, Oak Creek Realty Group, licensed in Missouri. Visit walterhayes.com

All trademarks are the property of their respective owners and may be registered marks in some countries. There is no affiliation or endorsement claim, express or implied, made by their use. AMSOIL products are formulated to meet or exceed the performance requirements set forth by the manufacturers of all applications shown here.

Contact Info

Premium Engine Care

Walter and Regina Hayes

1-417-649-6776 Call/Text

LOCATION:

Carl Junction, MO 64834

Products

  • Hydraulic Oil
  • Compressor Oil
  • Transmission Fluid
  • Gear Lube
  • Fuel Additives
  • Greases

Equipment

  • Auto/Light Truck
  • V-Twin Motorcycle
  • Metric Motorcycle
  • ATV & UTV
  • Marine
  • Diesel
  • Snowmobile
AMSOIL Authorized Dealer

Lookup Guides

  • Motorcycle
  • Snowmobile
  • ATV
  • UTV
  • Marine Outboard
  • PWC
  • Heavy Duty On-Road
  • Heavy Duty Off-Road
  • Agriculture

© Premium Engine Care. All Rights Reserved.

As an Amazon Associate I earn from qualifying purchases. AMSOIL links are Premium Engine Care dealer links.